SkiDoo MXZ700 '00-'03

MXZ700 Engine Options
$289.00 Dynoport Single Pipe....+5 HP @ 78-7900rpm....(add $100.00 for Ceramic Coating)
Great boost in low and midrange power.  True 5hp gains, MCB dyno-tested.
Note: '02 Models require the Dynoport Silencer in conjunction with the Single Pipe.  Single pipes does not work with stock silencer.
$249.00 Dynoport or MBRP Silencer....4 lbs weight reduction....slightly louder than stock
$260.00 V-Force Delta III Reeds....+3HP  P/N V3S-123-2
Adds +4 to 5HP when combined with pipe/port/head
$59.00 Fett Reed Spacers....+1HP
Adds a total of 2.5HP when combined with the Carbon Tech Reed Petals.
$280.00 Head Modification and Cylinder Shim Kit....+6 HP @ 7800-8000rpm
MCB machines your stock head to obtain stock squish when combined with the cylinder shim kit. This head does not increase compression; Bolt-on application.  This kit greatly improves top-end on the MXZ700.  Retains stock appearance.  This kit greatly improves midrange and top-end on the MXZ700.  Retains stock appearance.  This design eliminates detonation that causes the many crank failures seen on the 700's.  We have never seen a 700 crank fail after installing this kit.
$400.00 Cylinder Porting (with above Cylinder kit)....+4 to 5 HP
$69.95 UFO's....+5 HP low and mid only
Applies to '99-2000 models only.  UFO's can be tough to dial-in properly, however once they are set up properly, this is the
cheapest HP that you can buy.  We have tuned several, and have the proper notes to eliminate your test and tune time.
$250.00

MCB Moly-Coated OEM-Style Piston Kit
All MCB pistons are MOS2 coated; proven to be the best for durability and lubricity.  The piston material is high silicone content to give the necessary hardness that aluminum pistons need.  The piston-tops are hard anodized for heat resistance and to minimize piston expansion/contraction; this combined with the coating virtually eliminates the possibility of cold seizure.  All pistons are EXACT OEM dimensions and mass, including ring grooves (we actually use OEM rings).  These pistons offer equal or BETTER than OEM performance at significantly less cost.  All kits include everything necessary to rebuild your sled.  Pistons, rings, wrist pins, circlips, and a complete gasket kit.
$525.00
($165.00 Bottle-only)		 Holtzman Nitrous (NOS) Kit
45 instant HP!! NOS airbox-injected for safe and reliable HP.  Bottle pressure is not determined by bottle-temperature.  Constant pressure at all times.  Fuel Jets $20.00 each, specify Carb or EFI.
$159.00
Holtzman Engineering TempaFlow II
Automatic temperature-responding jetting adjustments for Non-DPM equipped models.
$210.00 Holtzman ATAAC....Temperature and Altitude automatic compensation all-in-one
$59.95 AD Boivin Front-End Handling Kit
This kit re-positions your radius rods for reduced body roll.  This truely makes a significant handling improvement on a ZX chassis.
 
148.5 peak HP potential with all of the above listed options.
  UFO quoted HP is only applicable in the low and midrange, and is not factored into the 148.5 HP figure.

Note:  All of the above listed options work for either DPM or non-DPM equipped models
 
MXZ700 Clutching Options
$249.95 SuperTorquer Heelclicker Kit (TRA)
The advantage of the Heelclicker is that it uses the steeper angles of the TRA clutch sheaves, yet provides more efficient belt-squeeze at the middle-to-upper end, simliar to a Polaris, Arctic Cat, or Comet-style clutch.  The Heelclicker also gives you full adjustability of weight placement, spring rates, engagement, top-shift, and more, therefore making it practical for grass drags, trail riding, lake racing, and mountain riding.  We have an excellent setup for fast-trail and racing at sea level, moderate snow conditions.
$159.00 EPI Trail Clutch Kit
$374.00 Team Roller Clutch TSS-04 and Clutch Kit
The Team Roller Clutch eliminates "clutch binding" as seen on the stock SkiDoo secondary.  The encapsulated design does not allow the moveable sheave to wobble, therefore eliminating bind, making upshift and backshift considerably smoother and more efficient.
$199.00 MCB Clutch Kit
Includes ramps, helix, pin weight, and both springs
$149.95 EPI Trail Clutch Kit (TRA)
Kit includes primary spring, secondary spring, helix, and pins.  Extremely responsive corner-to-corner for trail riding. Much improved backshifting and throttle response.
$199.95 Drag Clutch Kit (TRA).............................................................................................................................
Kit includes primary spring, helix, secondary spring, ramps, and pins.  This is a great 600' drag kit, sacraficing backshift for wicked upshifting.

SPECIAL  COMBINATION PACKAGES RECEIVE ADDITIONAL DISCOUNTS.
WE'VE GIVEN YOU THE MENU, CALL TO ORDER THE OPTIONS YOU LIKE.
 
$45.99 Ski-Doo Tunnel Protection Kits....for 1.0" Tracks and 1.25" Tracks
$29.95 Standard Tunnel Protection
$52.95 SkiDoo OEM Drive Belt....P/N 417-300-067
$33.00 Amsoil Dominator Oil (Gallon)
$29.00 Amsoil Interceptor Oil (Gallon)
$26.00 Amsoil HP Injector Oil (Gallon)
 
 
Traction and Control (Carbide Runners and Studs)
$69.95 Stud Boy Carbide Runners….9" G-Force  P/N 2153-00
$49.95 Stud Boy Carbide Runners….6" Switch-Back  P/N 2152-00
$59.95 Stud Boy Shaper Carbide Runners....4.5"
$69.95 Stud Boy Shaper Carbide Runners....6"
$79.95 Stud Boy Shaper Carbide Runners....7.5"
$89.95 Stud Boy Shaper Carbide Runners....9"
$40.95 Stud Boy 4" for Precision Skis....P/N 2255-00
$49.95 Stud Boy 6" for Precision Skis....P/N 2256-00
$89.00 Stud Boy "Deuce" Bar, Dual-Runners....4.5"
$99.00 Stud Boy "Deuce" Bar, Dual-Runners....6.5"
$140.00 Stud Boy "Deuce" Bar, Dual-Runners....9"
   
$1.40 ea Stud Boy 'SPT' or Woody's 'Excel' carbide studs w/ standard aluminum backer (complete)
$1.50 ea Stud Boy 'SPT' or Woody's 'Excel' carbide studs with 'Power Plate' backer (complete)
$1.08 ea Stud Boy 'SPT' or Woody's Excel' carbide studs (studs & nuts only)
$1.75 ea Stud Boy 'Power Point' Studs with standard aluminum backers (complete)
$1.85 ea Stud Boy 'Power Point' Studs with 'Power Plate' backers (complete)
$1.50 ea Stud Boy 'Power Point' Studs (studs and nuts only)
   
$1.60 ea Woody's 'Traction Master' Studs (stud & nut only)
$1.85 ea Woody's 'Traction Master' Studs with standard aluminum backer
$1.95 ea Woody's 'Traction Master' Studs with 'Power Plate' backer
$1.32 ea Woody's 'Mega Bite' Studs (stud & nut only)
$1.62 ea Woody's 'Mega Bite' Studs with standard aluminum backer
$1.72 ea Woody's 'Mega Bite' Studs with 'Power Plate' backer
(call) Stainless Steel Studs Available
$.40 ea Stud Boy 'Power Plate' backers (backers only, natural color)
Colored 'Power Plate' aluminum backers also available in Blue/Green/Red/Purple....add $.35 over natural-colored Power Plate

SPT's and Excel's come in .875" / 1.00" / 1.075" / 1.080" & (1.175" in Woody's only)
PowerPoints and Traction Master studs come in .875" / 1.00" / 1.075" / 1.080" / 1.175" / 1.187" / 1.325" / 1.5" / 1.625" / 1.750" sizes.

 See traction page for other Stainless Steel Studs, Ice Pixx, Assassains, Catapults, Chisels or Woody's Studs.

Studding Notes:  MCB recommends the 'Power Point' with the 'Power Plate' for all applications over 90HP. These studs have better penetration than the 'SPT' or 'Excel' stud.  MCB recommends the 'Power Plate' backer for any application over 1.08" in length regardless of HP. The 'Power Plate' gives the stud much better support than the standard aluminum backer, less deflection results in less stress & potential tearing of your track.

* For large volume orders of performance parts and/or traction products, further DISCOUNTS can be given on most items.  Call us and we'll make you the best deal !

 


Back to Home Page